-
1 locknut pipe thread
Abbreviation: NPSLУниверсальный русско-английский словарь > locknut pipe thread
-
2 гаечная резьба
1) General subject: female screw2) Engineering: internal thread3) Construction: nut thread4) Oil: female thread5) Mechanic engineering: locknut thread -
3 гайка
nut
-, анкерная — anchor nut
-, барашковая — wing nut
-, глухая — cap nut
-, затяжная (возд. винта). — retaining nut
-, колпачковая (заглушка) — cap nut
-, контровочная (контргайка) — locking nut, locknut
-, корончатая — castellated nut
-, манжетная — packirfg nut
-, накидная (рис. 101) — coupling /union/ nut
-, плавающая — floating nut
- распорной втулки (колеса) (рис. 32) — sleeve nut
- с вырезами под вилочный ключ, круглая — spanner nut
- с двумя ребрами на ципиндрической боковой поверхности — two-ribbed nut
- с накаткой — knurled nut
- с четырьмя ребрами на ципиндрической боковой поверхности — four-ribbed nut
-, самоконтрящаяся — self-locking nut
не допускается установка сомоконтрящихся гаек на болты, служащие в качестве осей, — no self-locking nut may be used on any bolt subject to rotation during airplane operation.
-, самотормозящаяся (самоконтрящаяся) — friction nut
-, слабозатянутая — loose nut
-, стопорная — retaining nut
-, четырехгранная — square nut
-, шестигранная (самопроизвольное) отворачиванне г. — hexagonal nut loosening of the nut
завертывать г. — screw on the nut
завертывать г. до соприкосновения с — turn the nut down until it contacts
завертывать г. на c6eг резьбы — start the nut on the thread
завертывать г. от руки — finger tighten the nut, screw the nut f7nger-tight
завинчивать г. — screw on the nut install the bolts in the holes and screw on the nuts.
затягивать г. — tighten the nut
затягивать г.до отказа — tighten the nut fully
затягивать г. моментом до кгм — tighten the nut by torque not exceeding kg-m
затягивать г. моментом кгм — tighten the nut to kg-m
затягивать г. моментом от до кгм kg-m — tighten the nut to to
затягивать г. на (3) нитки резьбы — tighten the nut (3) threads
затягивать г. от руки — finger tighten the nut
затягивать г. попеременно и равномерно — tighten the nuts alternately and evenly
затягивать г. равномерно — apply torque to the nut with steady even pressure
затягивать г. туго — tighten the nut tightly
контрить г. — lock the nut
навертывать г. — screw on the nut
наворачивать г. на болт — screw the nut on the bolt
наживлять г. — start the nut on thread
ослаблять г. — back /loosen/ the nut off
ослаблять затяжку г. на один оборот — back the nut off one revolution
ослаблять затяжку г. на одну грань — back the nut off one flat
ослаблять затяжку (корончатой) г. на одну — back the nut off one castellaгрань tion
отвертывать г. полностью — remove the nut
отворачивать r. — unscrew the nut
отворачивать г. на оборотов — back out the nut revolutionsРусско-английский сборник авиационно-технических терминов > гайка
См. также в других словарях:
Distorted thread locknut — A distorted thread locknut,[1] is a type of locknut that uses a deformed section of thread to keep the nut from loosening from vibrations or rotation of the clamped item. They are broken down into three types: elliptical offset nuts, centerlock… … Wikipedia
Nut (hardware) — A nut threaded onto a bolt A nut is a type of hardware fastener with a threaded hole. Nuts are almost always used opposite a mating bolt to fasten a stack of parts together. The two partners are kept together by a combination of their threads… … Wikipedia
Cogset — A freehub (above) for use with a cassette and a threaded hub (below) for use with a freewheel. On a bicycle, the cogset or cluster[1] is the set of multiple rear sprockets that attaches to the hub on the rear wheel. A cogset works with a rear… … Wikipedia
Headset (bicycle part) — The headset is the set of components on a bicycle which provide a rotatable interface between the bicycle fork and the bicycle frame itself. The short tube through which the steerer of the fork passes is called the head tube. A typical headset… … Wikipedia
Bolted joint — Bolted joints are one of the most common elements in construction and machine design. They consist of cap screws or studs that capture and join other parts, and are secured with the mating of screw threads.There are two main types of bolted joint … Wikipedia
List of bicycle parts — This is a list of bicycle parts.*Axle *Ball bearing *Bar ends extensions at the end of straight handlebars to allow for multiple hand possitions. *Basket cargo carrier *Bottle cage a holder for a water bottle *Bottom bracket The bearing system… … Wikipedia
Fixed-gear bicycle — A fixed gear bicycle or fixed wheel bicycle, is a bicycle without the ability to coast. The sprocket is screwed directly on to the hub and there is no freewheel mechanism. A reverse thread lockring is usually fitted to prevent the sprocket from… … Wikipedia
Split beam nut — A split beam nut is a locknut with slots cut in the top that separate the outside end into four or more sections that are bent slightly inward, making the thread diameter undersized in the slotted portion. As the nut is threaded on, these… … Wikipedia
Symbian — This article is about the operating system. For other uses, see Symbian (disambiguation). Symbian Company / developer Accenture on behalf of Nokia [1] … Wikipedia
interrupted screw — /ɪntəˌrʌptəd ˈskru/ (say intuh.ruptuhd skrooh) noun a screw with a discontinuous helix, as in a cannon breech, formed by cutting away part or parts of the thread, sometimes with part of the shaft beneath, used with a corresponding locknut …
